Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Parts & Accessories

For cyclists seeking maximum power transfer but also a minimal amount of float, Shimano’s SM-SH12 Blue cleats are the answer. By placing the pivot point at the front, lateral sliding movement is eliminated. But these cleats still permit a small amount of angle change from the pivot point back towards the heel so that your foot is not completely locked in place. • Blue SPD-SL cleats have 2 degrees of float – 1 degree in each direction • Shimano’s newest cleat option – a middle-ground between yellow (SM-SH11) and blue (SM-SH12) • Allows for a small range of movement while still delivering a high amount of pedaling efficiency • Float’s Pivot point is at the front of the cleat, eliminating lateral sliding movement while allowing a small amount of angle change from the pivot point back towards the heel
$9.99
The Curve Sole Measurement Tool works in conjunction with the flat sole shims to correct the radius of flat sole shoes and prevent unwanted squeaking. There are 4 radius measurements, one per side, that measure the sole and indicate whether a shim is needed or not.
$10.00
- Protects cranks from damage caused by overtightening pedals - Can be used for bike fit adjustments, dependent on pedal thread length engagement
$10.49
Shorter 7mm rear load pins for the outer extremities of SPOON, SPIKE, and OOZY pedals. - Provide durability and improved safety - Mix and match with the longer stock pins to customize your ideal amount of grip
$10.99
Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.
$11.50
Lost an end cap from your Penthouse Flat Mk5 Pedals? 2 x MK5 End Caps These also work for MK4 Penthouse flat pedals.
$13.99
IGUS Bushing replacements for your Spike or Oozy pedals help to eliminate any play that develops over time, and revive smooth spinning action. - 2pcs IGUS self lubricating bushing - 2pcs O-ring - 2pcs stainless shim washer
$13.99
Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included
$14.99
Crank boots designed for RaceFace Next R cranksets.
$15.00
Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs
$15.00
- Strapless resin construction - Strapless design - Tough and lightweight, ideal for urban conditions with frequent stops
$15.00
- Double tongue resin toe-clips - Nylon straps with steel buckles
$17.50 - $29.99
Everything you need to keep those Crank Bros pedals spinning freely is found in their Pedal Rebuild Kit. Each kit includes parts and instruction to rebuild one pair of Crank Bros. pedals.
$19.50
Spare Pedal Pins for the Composite MK4 Pedals. Keep maximum traction on your pedals with new Pedal Pins. - 32 Pedal Pins - Enough for a pair of pedals - Used for MK4 Composite Pedals only
$19.99
Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Candy 7 & 11 - Model years 2016 – present
$19.99
The Keo Spacer adaptors are slim wedges that fit between the shoe and the cleat. They aim to avoid the unpleasant creaking sound provoked by contact between the sole and the cleat, which can arise in particular with flat-soled shoes. Delivered with 2 spacers and 6 screws for quick and easy installation.
$19.99
These cleats work with LOOK Delta pedals. Mounting bolts and washers included.
$20.00
Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.
$20.00
The KEO cleat covers are designed to protect your KEO cleats while walking. Compatible with KEO GRIP and KEO CLEAT, these covers lengthen the life of your cleats and improve safety when walking thanks to an anti-slip surface. - Compatibility: KEO Grip/KEO Cleat - Use: Protect the cleat
$23.50
Spare Pedal Pins for the Penthouse Flat MK5 Pedals. Keep maximum traction on your pedals with new Pedal Pins. - 32 Stainless Steel Pedal Pins - Enough for a pair of pedals - Can be used for MK5 Penthouse flat pedals only
$24.99
Customize your 5050 pedals with Crank Brothers' Plate Kit. These anodized beauties bolt onto your existing pedals to give you style to match your skills.
$24.99
Everything you need to fully rebuild OneUp Composite pedals. MAINTENANCE INSTRUCTIONS 1. remove outer and inner end caps with 6mm hex key. 2. remove axle nut using 9mm socket. Drive side pedal (RH pedal) has left hand (reverse) threaded nut. Non Drive side pedal (LH pedal) has regular right hand threaded nut. 3. pull axle out of pedal body 4. push inner bearing out with 6mm hex 5. to replace bushing use a flat head screw driver to pry against the inner surface of the bushing to pull it out. You will destroy the bushing by removing it. 6. remove axle seal (take note of direction) REPLACEMENT INSTALL 1. grease new bushing and axle. Place bushing on axle and push it into pedal body. 2. replace pedal seal (thicker portion near flange of axle) 3. grease and place new bearing back into pedal body 4. slide axle through pedal body and bearing 5. replace axle nut 6. replace both end caps
$24.99
Everything you need to fully rebuild your OneUp Composite Pedals. KIT CONTAINS - 2 CARTRIDGE OUTER BEARINGS - 2 INNER DU BEARINGS - 2 OUTER SEALS - 2 AXLE NUTS
$25.00
HEIGHT ADJUSTMENT WASHERS AND PINS FOR OUR ALUMINUM PEDALS KIT CONTAINS - 40 - HEXIGONAL TIPPED M4 THREADED SOCKET HEAD PINS - 40 - 0.8mm THICK HEIGHT ADJUSTMENT WASHERS
$26.99
X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK Easy cleats provide a 13° angle of disengagement and allow for multidirectional release. - Compatibility: X-Track and Geo Trekking Collection, SPD compatible - Material: Premium Steel - Clip out direction: Multidirectional - Clip in: 30% easier - Angle of Disengagement: 13° - Lateral Adjustment: 2mm - Angular Adjustment: 1° - Weight (pair): 45g
$26.99
- Compatible with all Spike & Oozy Pedals - Full Complement Sealed Bearing x 2pcs - Green Silicone Friction Seals - Replacement inboard bearings for your SPIKE or OOZY pedals.
$28.00
Replacement pins for our Daemon pedals: - 5mm long - Made with 316 stainless steel - Precision CNC Machined in Whistler, B.C. - Sold in packs of 10
$29.99 - $30.00
The MADE by LOOK KEO standard is recognized in the cycling world for its minimal weight and compact design of the cleat and pedal combo. Of course, compatible with all pedals on the market, their memory positioner is a major advantage when changing your cleats. Their principle and use are the same as the DELTA cleat standard; engagement and disengagement remain efficient and reassuring. - Use: Road - Material: Polyamide + PTFE - Lateral adjustment: 4mm - Longitudinal adjustment: 12mm - Weight (pair + fasteners): 68g
$29.99
X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK cleats provide a 13° angle of disengagement and allow for unidirectional release only. - Compatibility: X-Track and Geo Trekking Collection, SPD compatible - Material: Premium Steel - Clip out direction: Lateral - Angle of Disengagement: 13° - Lateral Adjustment: 2mm - Angular Adjustment: 1° - Weight (pair): 45g
$29.99
Replacement cleats for all Shimano® SPD clipless pedals, featuring an easy-to-unclip multi-directional release. Ideal for casual or fitness riders looking for more clipless pedal confidence, these will allow you to clip out either on the outside or inside of the pedal. Lifting and twisting your heel can also release the pedal. Not recommended for performance off road and pavement riding, choose the SM-SH51 cleat instead.
Page 1 of 3 Next page