Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

Zipp Tangente Tube Wrench
$9.99
Zipp Speed Weaponry Valve Extender Wrench Set - Two 4 mm and 5 mm combination wrenches - Replacement wrenches required to properly install Zipp integrated valve extenders - Use with Zipp Tangente tubes with aluminum Presta valve and aluminum valve extender
Bontrager Wheel Magnets 
$9.99
Getting the correctly sized magnets means you're worrying about where the next coffee stop is, not if your computer is recording the ride. Key features: - Universal wheel magnets work with any speed sensor - Thread-on speed magnet is positioned closer to the sensor for improved signal - Aero speed magnet provides a sleek, low-profile, aerodynamic solution
Bontrager Tubeless Valves
$14.99 - $19.99
These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Silver MTB valve is compatible with all Bontrager Mountain wheels except: Line XXX, Kovee XXX, and Line Pro 40 - Alloy Road Tubeless Rim Valve is compatible with all Bontrager alloy TLR road wheels
Bontrager TLR Tubeless Rim Tape
$19.99
- To be used exclusively with Bontrager 29""/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Width : 21mm
Spank Oozy/Spike Rear Hub Adaptors
$29.99 - $34.99
Hub Adapters for all Oozy hubs and 2016 Spike hubs.
Shimano Alfine SG-S700 Oil Port Bolt
$8.99
Keeping contamination out of your internally geared hub is critical to its function and longevity. Sometimes, the oil port bolt comes loose and it's easy to lose, even if you've just taken it out to oil your hub. Keep a spare or two so your hub stays clean inside and it'll last you many, many miles.
Spank Oozy/Spike Rear Hub 135mm/142mm Axle Shafts
$24.99
Replacement axle for all Oozy hubs and 2016 Spike hubs.
Profile Design Campagnolo Freehub Body
$159.99
Profile Design's Campagnolo Freehub Body is the part you need to replace the Shimano/SRAM-compatible freehub body that comes stock on your Profile Design Altair or Armada wheels. Once installed on your wheel, the Campagnolo body lets you run Campy 9-, 10-, and 11-speed cassettes (sold separately).
DT Swiss Spoke Head Washer
$94.99
- Designed to stabilize 15g spokes in most hub flanges
DT Swiss Prolock Hexhead Alloy Nipples
$114.99
- ProLock: pre-prepped/treated nipple threads with special compound - Hexhead (14g only) design for building/truing at nipple head, in addition to 4-sided flats at rim protrusion - Form-A design assures smooth fit and build - Cold-forged nipple blank machined to DIN 79012 specs - 14mm overall length (2mm taller hexhead for wrench interface, but protrusion through rim is the same as a 12mm DT nipple) - 2.0mm (14g) spoke thread interface with full run-through - Made in Switzerland. - Box/100
Bontrager Elite Skewers
$34.99
Bontrager's new Elite Skewers better integrate into your frame for better aerodynamics and aesthetics, while the premium internal cam design ensures these are here to last Key features: - New Elite Skewer integrates better into the frame for optimized aerodynamics - Internal cam design looks great, lasts longer, and offers quick, easy operation
SRAM Conversion Cap & XD Driver Body for Roam 60/50 and Rail 50 Wheel
$189.99
Convert your SRAM Roam 60, 50 or Rail 50 wheels to SRAM 11-speed with the XD Driver Body and Axle Cap. XD is a cassette driver body that allows the use of a 10-tooth small cog and provides an improved interface with the cassette. The axle cap is specific to the XD driver and your preferred axle choice.
CushCore Pro
$249.99
The revolutionary tire insert! RIDE FASTER! CushCore provides a 12% smoother ride and 3% reduced rolling resistance. Ride with more control, more momentum, and less fatigue. It’s like taking fewer punches in a fight. CORNER HARDER! 35% more sidewall stability eliminates tire squirm and burping, even at low tire pressure. Rail corners with total confidence. GO BIGGER! CushCore improves suspension performance by 16% and reduces impact force from big hits by 50%. Send it with total confidence. HOW CUSHCORE WORKS: CushCore is based on a new concept: Tire Suspension. Any suspension system has a spring and a damper, and with CushCore, pressurized air in the tire is the spring and the CushCore tire insert is the damper. Also like traditional suspension, a constant damping force wouldn’t work. It has to be dynamic. Suspension should be supple on small bumps but firm on big hits. CushCore responds differently depending on the tire loading scenario. The more the tire flexes, the more damping it provides. We break it down into small, medium, and large tire deflections.
Robert Axle Project Rear Lightning Bolt-On Thru Axle
$94.99
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
Stan's NoTubes Neo Speedsync Freehub
$199.99
Stan's original Neo hub has evolved to be stronger and more reliable than ever. The additional stress of larger cassette cogs, more capable bikes, and even more challenging trails led to the creation of the Neo with Speedsync. This CNC machined Speedsync freehub is a direct replacement for your Neo hub and includes pawls, springs, pawl retaining ring, and 2 red freehub spacers. Bearings are pre-installed. Note: - Singlespeed freehub cannot be used to convert a hub originally set up with a Shimano or Sram XD freehub to SS. This freehub is only to be used with Stan's Neo SS hubs. - OneUp freehub WILL NOT WORK with a SRAM cassette or Shimano cassette without a One Up Shark Cluster.
Spank Spike DH Rear Hub Bearing Kit
$49.99
More robust bearings for Spike DH hubs.
Spank Oozy/Spike Bearing Kit
$49.99
Replacement bearings for OOZY Trail F15/20 or SPIKE F20/15 Front Hubs. Compatible with all OOZY hubs and wheels. Compatible only with SPIKE and SPOON wheels produced in 2016 or later (with SPIKE hubs). - Material : Steel - Weight (g): Front ±35 Rear ±62 - Compatibility : OOZY/SPIKE Front & Rear Hubs
Spank Spike DH Rear Hub Adaptor
$29.99
Converts SPIKE DH R150 Rear Hubs to 12x157mm. Compatible only with SPIKE and SPOON (150mm) wheels produced in 2015 or later (with SPIKE hubs). - Material : Alloy - Weight (g): ±14 - Compatibility : SPIKE DH 12x150mm Rear Hubs
Shimano Alfine S7000/S700 Shift Cable Fixing Bolt Unit
$8.99
Need a Shift Cable Fixing Bolt Unit for your Alfine S7000/S700 hub? Here it is. Now, get that bike back on the road!
Stan's NoTubes Neo Rear Hub End Caps
$31.99
Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place
Stan's NoTubes 3.30/3.30Ti Hub Kit
$34.99
Stan's 3.30/3.30Ti Hub Kit converts Stan's 3.30 front hubs from quick-release to through-axle compatible. Installation is easy—just pull the old ones off and put the new ones on. Conversion kits available in 12mm and 15mm.
Wheels Manufacturing Inc. Axle-06
$24.99
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs - Type: Solid Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 174mm - 1 axle per bag
Spank Oozy/Spike Freehub Bodies
$124.99 - $134.99
Replacement cassette bodies for Oozy hubs and Spike hubs. - Shimano or SRAM - Alloy or Steel
Robert Axle Project BOB Trailer Thru Axle
$84.99 - $124.99
Yes! A 12mm thru-axle adapter for BOB Trailers. These Robert Axles for BOB Trailers are specifically engineered to attach the proven BOB Trailer to your thru-axle-equipped bike. Take full advantage of your modern bike with 12mm thru-axles and harness the rigidity of the thru-axle to haul your BOB Trailer. Set out on any adventure, big or small. Great for off-road tours, trail building, hauling cargo, and more! - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The axle ends are stainless steel which allows for mounting of the BOB Trailer bobbins. - No special tools required. The design allows for wheel installation or removal using your standard 5mm hex wrench. - Please note: This axle does not come with the BOB Trailer bobbins (those are available separately). Or, you can reuse your bobbins from the stock BOB Trailer Quick Release that came with your trailer. - Designed, built, and quality tested in the USA. Proven around the world.
Robert Axle Project Front Lightning Bolt-On NAILD Thru Axle
$114.99
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
SRAM XD Driver Freehub Body for 746 Rear Hub
$99.99
- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap
Shimano Alfine S700 Cassette Joint Unit
$39.99
Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S700 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S700
SRAM X0 Hub Conversion Caps
$24.99
SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.
Shimano Alfine S7000 Cassette Joint Unit
$29.99
Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S7000 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S7000-8
Robert Axle Project Front Lightning Bolt-On Thru Axle
$84.99
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
Page 1 of 6 Next page