Parts & Accessories

The Curve Sole Measurement Tool works in conjunction with the flat sole shims to correct the radius of flat sole shoes and prevent unwanted squeaking. There are 4 radius measurements, one per side, that measure the sole and indicate whether a shim is needed or not.

Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.

Lost an end cap from your Penthouse Flat Mk5 Pedals? 2 x MK5 End Caps These also work for MK4 Penthouse flat pedals.

IGUS Bushing replacements for your Spike or Oozy pedals help to eliminate any play that develops over time, and revive smooth spinning action. - 2pcs IGUS self lubricating bushing - 2pcs O-ring - 2pcs stainless shim washer

Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included

Crank boots designed for RaceFace Next R cranksets.

Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs

HEIGHT ADJUSTMENT WASHERS AND PINS FOR OUR ALUMINUM PEDALS KIT CONTAINS - 40 - HEXIGONAL TIPPED M4 THREADED SOCKET HEAD PINS - 40 - 0.8mm THICK HEIGHT ADJUSTMENT WASHERS

Everything you need to keep those Crank Bros pedals spinning freely is found in their Pedal Rebuild Kit. Each kit includes parts and instruction to rebuild one pair of Crank Bros. pedals.

Everything you need to fully rebuild your OneUp Composite Pedals. KIT CONTAINS: - 2 CARTRIDGE OUTER BEARINGS - 2 INNER DU BEARINGS - 2 OUTER SEALS - 2 AXLE NUTS - 2 INNER CAPS - 2 END CAPS

Spare Pedal Pins for the Composite MK4 Pedals. Keep maximum traction on your pedals with new Pedal Pins. - 32 Pedal Pins - Enough for a pair of pedals - Used for MK4 Composite Pedals only

Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Candy 7 & 11 - Model years 2016 – present

- Double tongue resin toe-clips - Nylon straps with steel buckles

These cleats work with LOOK Delta pedals. Mounting bolts and washers included.

Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.

Spare Pedal Pins for the Penthouse Flat MK5 Pedals. Keep maximum traction on your pedals with new Pedal Pins. - 32 Stainless Steel Pedal Pins - Enough for a pair of pedals - Can be used for MK5 Penthouse flat pedals only

Everything you need to fully rebuild your OneUp Aluminum Pedals. Our V2 kit is compatible with all OneUp Aluminum pedals. The brass bushings take the place of the 3 small cartridge bearings and aluminum washer that were on our original pedal assembly. KIT CONTAINS - 2 LARGE OUTER BEARINGS - 2 BRASS BUSHINGS - 2 OUTER SEALS - 2 FLANGE WASHERS - LH AND RH AXLE BOLTS - 2 AXLE O-RINGS - LH AND RH BEARING NUTS

Customize your 5050 pedals with Crank Brothers' Plate Kit. These anodized beauties bolt onto your existing pedals to give you style to match your skills.

Everything you need to fully rebuild OneUp Composite pedals. MAINTENANCE INSTRUCTIONS 1. remove outer and inner end caps with 6mm hex key. 2. remove axle nut using 9mm socket. Drive side pedal (RH pedal) has left hand (reverse) threaded nut. Non Drive side pedal (LH pedal) has regular right hand threaded nut. 3. pull axle out of pedal body 4. push inner bearing out with 6mm hex 5. to replace bushing use a flat head screw driver to pry against the inner surface of the bushing to pull it out. You will destroy the bushing by removing it. 6. remove axle seal (take note of direction) REPLACEMENT INSTALL 1. grease new bushing and axle. Place bushing on axle and push it into pedal body. 2. replace pedal seal (thicker portion near flange of axle) 3. grease and place new bearing back into pedal body 4. slide axle through pedal body and bearing 5. replace axle nut 6. replace both end caps

Everything you need to fully rebuild your OneUp Composite Pedals. KIT CONTAINS - 2 CARTRIDGE OUTER BEARINGS - 2 INNER DU BEARINGS - 2 OUTER SEALS - 2 AXLE NUTS

Wheels Manufacturing Pedal Washers help distribute the forces of a pedal spindle on your expensive crank arms and allow you to torque pedals properly over and over again without damaging crank arms.

- Compatible with all Spike & Oozy Pedals - Full Complement Sealed Bearing x 2pcs - Green Silicone Friction Seals - Replacement inboard bearings for your SPIKE or OOZY pedals.

Replacement pins for our Daemon pedals: - 5mm long - Made with 316 stainless steel - Precision CNC Machined in Whistler, B.C. - Sold in packs of 10

The Cleat Shim-Spacer helps compensate for leg length discrepancies.

The DELTA standard requires a rotational movement of the foot toward the outside or inside for disengagement. This function improves cyclist's safety; no body or bearing prevents disengagement toward the inside. Compatible with non-KEO LOOK pedals, their contact area is wide for optimal comfort. They also feature a memory positioner to aid when changing cleats. - Use: Road & Indoor Bike - Material: Polyacetal + PTFE - Lateral adjustment: 4mm - Longitudinal adjustment: 12mm - Weight (pair + fasteners): 75g

The MADE by LOOK KEO standard is recognized in the cycling world for its minimal weight and compact design of the cleat and pedal combo. Of course, compatible with all pedals on the market, their memory positioner is a major advantage when changing your cleats. Their principle and use are the same as the DELTA cleat standard; engagement and disengagement remain efficient and reassuring. - Use: Road - Material: Polyamide + PTFE - Lateral adjustment: 4mm - Longitudinal adjustment: 12mm - Weight (pair + fasteners): 68g

Replacement cleats for all Shimano® SPD clipless pedals, featuring an easy-to-unclip multi-directional release. Ideal for casual or fitness riders looking for more clipless pedal confidence, these will allow you to clip out either on the outside or inside of the pedal. Lifting and twisting your heel can also release the pedal. Not recommended for performance off road and pavement riding, choose the SM-SH51 cleat instead.

Replacement cleats for RXS pedals, featuring "Cafe" profiling, which means that when you walk into your local coffee shop for a mid-ride refreshment, you don't risk slipping and falling on the tile floor.

The XPro & Xpresso cleats have been developed for the TIME XPro & Xpresso road bike pedal range. They allow angular and lateral freedom in order to respect the natural movements of your legs and joints. You can also adjust the Q-factor (by switching the cleats) in order to optimize performance, following 3 points: security, ergonomics, and performance. The Bi-material brings more durability when walking with the cleats. These cleats are the stock cleats included with all XPro & Xpresso pedals.

- Set of 44 total replacement steel pins for vault pedals - Run threads-out for maximum traction or flip the pins to heads-out for less grip - 16 Short pins (for use in the center) overall length 8.5mm, stud is 4.5mm - 28 Long pins (for use in the outside edge) overall length 12.5mm, stud is 4.5mm - Use either a 5mm spanner or the included 2mm hex wrench to secure/remove