Parts & Accessories

- The ATAC EASY 10° cleat works with all TIME mountain pedals. - Included with mountain pedal models numbered "2" and "4." - Release angle of 10 degrees and is compatible with all two-hole cycling shoes. - Don't let the "Easy" name fool you. If you are a high-performance rider looking to reduce the release angle from our 17 or 13 degrees, this is the choice for you.

- Developed for the TIME XPRO & XPRESSO road bike pedal range. - They allow angular and lateral freedom in order to respect the natural movements of your legs and joints. - You can also adjust the Q-factor (by switching the cleats) - The Bi-material brings more durability when walking with the cleats. - These cleats are the stock cleats included with all XPRO & XPRESSO pedals.

Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals

Everything you need to keep those Crank Bros pedals spinning freely is found in their Pedal Rebuild Kit. Each kit includes parts and instruction to rebuild one pair of Crank Bros. pedals.

Look's Keo Grip Cleats feature special anti-slip surfaces on the bottom that improve traction while walking. They are also made of polyamide nylon for easy entry/exit, efficient pedaling and durability. And, there are wear indicators that tell you when it's time for new cleats. These cleats are available with three different amounts of lateral float: 4.5-degree (gray), 9-degrees (red), and fixed float (black).

Everything you need to fully rebuild OneUp Composite pedals. MAINTENANCE INSTRUCTIONS 1. remove outer and inner end caps with 6mm hex key. 2. remove axle nut using 9mm socket. Drive side pedal (RH pedal) has left hand (reverse) threaded nut. Non Drive side pedal (LH pedal) has regular right hand threaded nut. 3. pull axle out of pedal body 4. push inner bearing out with 6mm hex 5. to replace bushing use a flat head screw driver to pry against the inner surface of the bushing to pull it out. You will destroy the bushing by removing it. 6. remove axle seal (take note of direction) REPLACEMENT INSTALL 1. grease new bushing and axle. Place bushing on axle and push it into pedal body. 2. replace pedal seal (thicker portion near flange of axle) 3. grease and place new bearing back into pedal body 4. slide axle through pedal body and bearing 5. replace axle nut 6. replace both end caps

The MADE by LOOK KEO standard is recognized in the cycling world for its minimal weight and compact design of the cleat and pedal combo. Of course, compatible with all pedals on the market, their memory positioner is a major advantage when changing your cleats. Their principle and use are the same as the DELTA cleat standard; engagement and disengagement remain efficient and reassuring. - Use: Road - Material: Polyamide + PTFE - Lateral adjustment: 4mm - Longitudinal adjustment: 12mm - Weight (pair + fasteners): 68g

Customize your 5050 pedals with Crank Brothers' Plate Kit. These anodized beauties bolt onto your existing pedals to give you style to match your skills.

Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.

HEIGHT ADJUSTMENT WASHERS AND PINS FOR OUR ALUMINUM PEDALS KIT CONTAINS - 40 - HEXIGONAL TIPPED M4 THREADED SOCKET HEAD PINS - 40 - 0.8mm THICK HEIGHT ADJUSTMENT WASHERS

A revolution in performance and reliability. The kit includes premium internal components: - Inner bearing o-ring x 2 - Spindle seal x 2 - Outer Igus solid bearing x 2 - Inner Igus solid bearing half x 4 - Bearing Retainer Bolt x 4 - Outer o-ring x 2 - Grease port screw x 2 - Compatibility: Stamp (2016), Stamp 7 (2017+), Stamp 11 (2017+)

Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Mallet E - Model years 2016 – present

Wheels Manufacturing Pedal Washers help distribute the forces of a pedal spindle on your expensive crank arms and allow you to torque pedals properly over and over again without damaging crank arms.

Replacement bearings and bushings specific to Spoon 90 (Small) and 100/110 (Medium and Large) pedals. Eliminates play that can develop over time, and revives performance. Includes: - Sealed Bearing x2pcs - 10mm IGUS Bushing x2pcs - Green Friction Seal x2pcs - Locknut - O-ring x 2pcs

Spare Pedal Pins for the Penthouse Flat MK5 Pedals. Keep maximum traction on your pedals with new Pedal Pins. - 32 Stainless Steel Pedal Pins - Enough for a pair of pedals - Can be used for MK5 Penthouse flat pedals only

Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included

- Works with all XPRO and XPRESSO pedals. - Not included with new XPRO and XPRESSO pedals. - This is a zero-float cleat design, so there are zero (0) degrees of heel float and no lateral float along the pedal axle. - Compatible with all three-hole road shoes, but the included shim may be required for shoes that have a large curvature in the forefoot area. Full details are included in the easy-to-use instructions.

Pedal Axle Rebuild Kit for SPIKE & OOZY Trail Pedals - 1 set L&R axle - 2pcs IGUS bushing - 2pcs O-ring - 2pcs dust cap - 2pcs stainless shim washer - 2pcs silicone friction seal - 2pcs lock nut

- The ATAC 13/17° cleat works with all TIME mountain pedals. - Included with all mountain pedal models numbered "6" and higher - Release angles of 13 degrees or 17 degrees depending on how the cleat is set up on the shoe - Compatible with all two-hole cycling shoes.

Replace or overhaul iSSi pedals with Bushing & Bearing Spindles with these handy kits, or customize your stance width with longer spindle options. Includes: - iSSi chromoly spindles - Sealed cartridge outer bearings - Inner Bushings - Spindle nuts - Seals - iSSi-branded end caps

Replacement cleats for all Shimano® SPD clipless pedals, featuring an easy-to-unclip multi-directional release. Ideal for casual or fitness riders looking for more clipless pedal confidence, these will allow you to clip out either on the outside or inside of the pedal. Lifting and twisting your heel can also release the pedal. Not recommended for performance off road and pavement riding, choose the SM-SH51 cleat instead.

Your pedals like to be pampered. The Crank Brothers Pedal Refresh Kit gives you everything you need to keep them happy. Pedal Refresh Kit includes: -Enduro catridge bearings - Igus LL-glide bearings - Double seal system (internal and external seals) - Hex alloy end caps - O-rings - Nuts - Sleeve bushings - Bearing removal tool Compatible with the following pedals (2010-present): - Eggbeaters - Candys - Mallets - 5050s

X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK Easy cleats provide a 13° angle of disengagement and allow for multidirectional release. - Compatibility: X-Track and Geo Trekking Collection, SPD compatible - Material: Premium Steel - Clip out direction: Multidirectional - Clip in: 30% easier - Angle of Disengagement: 13° - Lateral Adjustment: 2mm - Angular Adjustment: 1° - Weight (pair): 45g

The XPro & Xpresso cleats have been developed for the TIME XPro & Xpresso road bike pedal range. They allow angular and lateral freedom in order to respect the natural movements of your legs and joints. You can also adjust the Q-factor (by switching the cleats) in order to optimize performance, following 3 points: security, ergonomics, and performance. The Bi-material brings more durability when walking with the cleats. These cleats are the stock cleats included with all XPro & Xpresso pedals.

Synth Axle Kit

Replacement charging clips and Y-shaped cable for the POWRLINK ZERO Power Pedal System In the box - Y-shaped charging cable - Charging clips (x2)"

- Set of 44 total replacement steel pins for vault pedals - Run threads-out for maximum traction or flip the pins to heads-out for less grip - 16 Short pins (for use in the center) overall length 8.5mm, stud is 4.5mm - 28 Long pins (for use in the outside edge) overall length 12.5mm, stud is 4.5mm - Use either a 5mm spanner or the included 2mm hex wrench to secure/remove

Replacement pins for our Daemon pedals: - 5mm long - Made with 316 stainless steel - Precision CNC Machined in Whistler, B.C. - Sold in packs of 10

The KEO cleat covers are designed to protect your KEO cleats while walking. Compatible with KEO GRIP and KEO CLEAT, these covers lengthen the life of your cleats and improve safety when walking thanks to an anti-slip surface. - Compatibility: KEO Grip/KEO Cleat - Use: Protect the cleat

- Protects cranks from damage caused by overtightening pedals - Can be used for bike fit adjustments, dependent on pedal thread length engagement