Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Parts & Accessories

$8.99
Shorter 7mm rear load pins for the outer extremities of SPOON, SPIKE, and OOZY pedals. - Provide durability and improved safety - Mix and match with the longer stock pins to customize your ideal amount of grip
$9.99
The Curve Sole Measurement Tool works in conjunction with the flat sole shims to correct the radius of flat sole shoes and prevent unwanted squeaking. There are 4 radius measurements, one per side, that measure the sole and indicate whether a shim is needed or not.
$10.99
Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.
$11.50
Lost an end cap from your Penthouse Flat Mk5 Pedals? 2 x MK5 End Caps These also work for MK4 Penthouse flat pedals.
$11.99
IGUS Bushing replacements for your Spike or Oozy pedals help to eliminate any play that develops over time, and revive smooth spinning action. - 2pcs IGUS self lubricating bushing - 2pcs O-ring - 2pcs stainless shim washer
$11.99
Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included
$14.99
Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs
$14.99
Crank boots designed for RaceFace Next R cranksets.
$17.50 - $29.99
Everything you need to keep those Crank Bros pedals spinning freely is found in their Pedal Rebuild Kit. Each kit includes parts and instruction to rebuild one pair of Crank Bros. pedals.
$19.50
Spare Pedal Pins for the Composite MK4 Pedals. Keep maximum traction on your pedals with new Pedal Pins. - 32 Pedal Pins - Enough for a pair of pedals - Used for MK4 Composite Pedals only
$19.99
Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.
$19.99
Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Candy 7 & 11 - Model years 2016 – present
$19.99
- Double tongue resin toe-clips - Nylon straps with steel buckles
$19.99
The KEO cleat covers are designed to protect your KEO cleats while walking. Compatible with KEO GRIP and KEO CLEAT, these covers lengthen the life of your cleats and improve safety when walking thanks to an anti-slip surface. - Compatibility: KEO Grip/KEO Cleat - Use: Protect the cleat
$19.99
The Keo Spacer adaptors are slim wedges that fit between the shoe and the cleat. They aim to avoid the unpleasant creaking sound provoked by contact between the sole and the cleat, which can arise in particular with flat-soled shoes. Delivered with 2 spacers and 6 screws for quick and easy installation.
$19.99
These cleats work with LOOK Delta pedals. Mounting bolts and washers included.
$19.99
- Christophe Vintage leather strap - Celebrating 130 years of history - 370mm long - Metal buckle
$23.50
Spare Pedal Pins for the Penthouse Flat MK5 Pedals. Keep maximum traction on your pedals with new Pedal Pins. - 32 Stainless Steel Pedal Pins - Enough for a pair of pedals - Can be used for MK5 Penthouse flat pedals only
$24.99
Customize your 5050 pedals with Crank Brothers' Plate Kit. These anodized beauties bolt onto your existing pedals to give you style to match your skills.
$24.99
- Strapless design is easy to engage without fully committing to the pedal - No special shoes required - Improves pedaling efficiency - Molded from unbreakable nylon - Please make sure your pedals have visible mounting points or a removable reflector for mounting prior to purchase - Includes mounting hardware. Note: metal plate may not be required during installation.
$24.99
Everything you need to fully rebuild OneUp Composite pedals. MAINTENANCE INSTRUCTIONS 1. remove outer and inner end caps with 6mm hex key. 2. remove axle nut using 9mm socket. Drive side pedal (RH pedal) has left hand (reverse) threaded nut. Non Drive side pedal (LH pedal) has regular right hand threaded nut. 3. pull axle out of pedal body 4. push inner bearing out with 6mm hex 5. to replace bushing use a flat head screw driver to pry against the inner surface of the bushing to pull it out. You will destroy the bushing by removing it. 6. remove axle seal (take note of direction) REPLACEMENT INSTALL 1. grease new bushing and axle. Place bushing on axle and push it into pedal body. 2. replace pedal seal (thicker portion near flange of axle) 3. grease and place new bearing back into pedal body 4. slide axle through pedal body and bearing 5. replace axle nut 6. replace both end caps
$24.99
Everything you need to fully rebuild your OneUp Composite Pedals. KIT CONTAINS - 2 CARTRIDGE OUTER BEARINGS - 2 INNER DU BEARINGS - 2 OUTER SEALS - 2 AXLE NUTS
$24.99 - $49.99
Wheels Manufacturing Pedal Washers help distribute the forces of a pedal spindle on your expensive crank arms and allow you to torque pedals properly over and over again without damaging crank arms.
$25.00
- Pedal Carbon blade Kit TIME XPro QTY 4
$26.99
X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK cleats provide a 13° angle of disengagement and allow for unidirectional release only. - Compatibility: X-Track and Geo Trekking Collection, SPD compatible - Material: Premium Steel - Clip out direction: Lateral - Angle of Disengagement: 13° - Lateral Adjustment: 2mm - Angular Adjustment: 1° - Weight (pair): 45g
$26.99
X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK Easy cleats provide a 13° angle of disengagement and allow for multidirectional release. - Compatibility: X-Track and Geo Trekking Collection, SPD compatible - Material: Premium Steel - Clip out direction: Multidirectional - Clip in: 30% easier - Angle of Disengagement: 13° - Lateral Adjustment: 2mm - Angular Adjustment: 1° - Weight (pair): 45g
$26.99
Everything you need to fully rebuild your OneUp Composite Pedals. KIT CONTAINS: - 2 CARTRIDGE OUTER BEARINGS - 2 INNER DU BEARINGS - 2 OUTER SEALS - 2 AXLE NUTS - 2 INNER CAPS - 2 END CAPS
$28.00
Replacement pins for our Daemon pedals: - 5mm long - Made with 316 stainless steel - Precision CNC Machined in Whistler, B.C. - Sold in packs of 10
$29.99
The Cleat Shim-Spacer helps compensate for leg length discrepancies.
$29.99
The DELTA standard requires a rotational movement of the foot toward the outside or inside for disengagement. This function improves cyclist's safety; no body or bearing prevents disengagement toward the inside. Compatible with non-KEO LOOK pedals, their contact area is wide for optimal comfort. They also feature a memory positioner to aid when changing cleats. - Use: Road & Indoor Bike - Material: Polyacetal + PTFE - Lateral adjustment: 4mm - Longitudinal adjustment: 12mm - Weight (pair + fasteners): 75g
Page 1 of 3 Next page