Parts & Accessories

Stages Gen 3 single-sided Power L meter is built onto a non-drive-side Shimano GRX RX-810 crank arm. It's compatible with all Shimano GRX Cranksets. Tour Proven Stages Power has carried riders to three consecutive Tour de France victories, plus many more world and national championships. If you believe racing provides the world's best product-proving ground, then Stages Power is proven as the world's best power meter. Active Temperature Compensation as Standard Equipment Consistency of measurement is the most important feature of a power meter. Stages Power was the first meter to make temperature compensation an automatic process, ensuring accurate readings no matter the environmental conditions. Individual meter calibration for the most accurate results. Stages Power meters are calibrated individually to ensure a +/- 1.5% accuracy level. Individual calibration means that you can trust the data produced by our system. Additional features: - +/- 1.5% accuracy in all conditions - Active temperature compensation - Accelerometer-based cadence measurement - Wirelessly upgradable firmware - LED indicator displays battery level at start up (with no need to connect to an app) and confirms successful zero reset - Updated accelerometer and addition of gyroscope for improved cadence resolution - Upgraded BLE and ANT+ radios offer a 6X improvement of data transmission strength Specifications: - Accuracy: +/- 1.5% - Power meter housing: low-profile design, with robust door interface - Weight: Only adds 15g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) when used as a single-sided meter - Power range (Watts): 0 to 5000 - Cadence range (rpm): 10-220 - Water resistance rating: IPX7 Sizing Options: - Lengths: 170mm, 172.5mm 175mm Compatibility: - This Shimano GRX RX810 Stages Power meter is compatible with all Shimano GRX cranksets. - Frame Compatibility: Most frames - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibility: Stages Link, Training Peaks, Strava, Garmin Training Center, and others

Wolf Tooth's CAMO stands for Chainline and Material Optimization. Available in various chainlines and spider configurations, CAMO spiders allow the use of previously unavailable chainring styles, materials, and chainlines in a lightweight, modular, and customizable package. These spiders are for use with the RaceFace cranksets that have removable Cinch spiders/chainrings and are only compatible with CAMO rings and bolts. Three different chainline options are available. The number and letter refer to the mm offset and direction from the mounting face to the centerline of the teeth: - M8 (minus 8mm - dished toward the frame): For 49mm chainline, used with GXP and long-spindle BB30 cranks. Designed for bikes with 135mm QR, 142mm thru axle, and some 148mm bikes. - M5 (minus 5mm - dished toward the frame): For 52mm chainline (Boost) - P2 (plus 2mm - dished outward away from the frame): For fat bikes that have 190/197 rear spacing but use a 100mm-spindle crank

Wolf Tooth's CAMO stands for Chainline and Material Optimization. Available in various chainlines and spider configurations, CAMO spiders allow the use of previously unavailable chainring styles, materials, and chainlines in a lightweight, modular, and customizable package. These spiders are for use with the SRAM cranksets that have removable Direct Mount spiders and are only compatible with CAMO rings and bolts. Four different chainline options are available. The number and letter refer to the mm offset and direction from the mounting face to the centerline of the teeth: - M8 (minus 8mm - dished toward the frame): For 49mm chainline, used with GXP and long-spindle BB30 cranks. Designed for bikes with 135mm QR, 142mm thru axle, and some 148mm bikes. - M5 (minus 5mm - dished toward the frame): For 52mm chainline (Boost) - M2 (minus 2mm - dished toward the frame): For 49mm chainline on short-spindle BB30 cranks - P2 (plus 2mm - dished outward away from the frame): For fat bikes that have 190/197 rear spacing but use a 100mm-spindle crank. Can also be used to achieve a Boost chainline with a short-spindle BB30 crank.

Replacement crank arm for XX1 Eagle GXP

The Wheels Manufacturing PressFit 30 Bottom Bracket Adaptor for Shimano Cranks adapts 24mm Spindle Cranks (Shimano Hollowtech II, FSA, Race Face EXI, etc.) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SHIM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SHIM to adapt 24mm Spindle Cranks (Shimano, FSA, etc.) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

The X0 Eagle T-Type AXS™ Wide left crankarm with Power Meter spindle provides riders with accurate, live power data delivery housed in our most advanced aluminum crankset. The power meter technology is integrated through what SRAM calls “DUB-PWR” – a unique design that elegantly houses Quarq’s reliable and accurate power measurement inside the DUB crank spindle itself. Measuring left-side power to calculate total watts, it’s subtle, lightweight, compatible with any chainring setup, and boasts unbeatable battery life. It is also compatible with the Flight Attendant system, allowing for total connectivity between all AXS™ enabled components. No-compromise, no-fuss data delivery with robustness in mind. - Innovative "DUB-PWR" design allows for lightweight, subtle Quarq power integration - Compatible with RockShox Flight Attendant - Unique, groundbreaking design integrated with one of the lightest aluminum cranksets on the market - +/-3% accuracy means you'll always know your true watts output - Long battery life provides 400+ hours of usage - Waterproof (IPX7 waterproof to 1 meter for 30 minutes - Right arm, Bottom bracket, Chainring and Spider NOT included

Replacement crank arm for GX Eagle GXP

- Replacement bolt for DUB cranks

- Adapts American/Pro BMX frames with a non-Threaded 51.3mm (2.02") i.d. bottom bracket shell to accept English-threaded bottom bracket & crank applications - CNC-machined aluminum with three steel connecting bolts to prevent independent rotation

Shimano, FC-TX801, Crank Arm, 170mm, Square, Black

Replacement Integrated bash guard for MRP chain guides. Protects your expensive 1x or 2x chainrings and helps you glide over rocks and obstacles. V1 (Version 1) fits older model MRP 2X/XCG/AMG chain guides. V2 (Version 2) fits newer model MRP 2X/XCG/AMG chain guides.

The Wheels Manufacturing 386 EVO Adaptor for Shimano Hollowtech II Cranks adapts Shimano cranks to 386EVO-standard frames. Simply tap the adapters into the 6806 bearing in the BB shell or cups, then install the cranks using the included spacers to adjust chainline, or to take up any side-to-side movement in the crank. - Machined engineering-grade Delrin - 48g/pr Includes - (2) - 24mm ID adapters - (8 )- .7mm spacers

- Shimano, FC-MT500 Crank Arm, Crank Arm, 170mm, Hollowtech II, Black, Y1VB98030

Wheels Manufacturing Press Fit 30 Bottom Bracket Adapter for 22/24mm Spindle Cranks adapts 22/24mm Spindle Cranks (SRAM/TruVativ) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SRAM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SRAM to adapt 22/24mm Spindle Cranks (SRAM/TruVativ) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter

Used to adjust crank chainline or take up any slack when using 29mm (SRAM DUB) spindle cranks. - 29mm I.D. - 2.5mm thick - 5 spacers per bag - Machined engineering-grade Delrin

Used to adjust crank chainline or take up any slack when using 29mm (SRAM DUB) spindle cranks. - 29mm I.D. - 5mm thick - 5 spacers per bag - Machined engineering-grade Delrin

Eliminate dropped chains forever and protect your Yeti's expensive 1x chainring with the OneUp Components Bash Guide. The OneUp Bash Guide was developed with input from top EWS World racers and can be seen all over the EWS circuit. Reinforced Nylon bash guards and a back plate cut from 8mm thick 7075-T6 aluminum, ensure that the OneUp Bash Guide can handle the biggest hits, but at a weight of only 105g (34T) you might forget it’s even there. NOT JUST FOR ENDURO RACERS. The OneUp Bash Guide is equally at home on your trail bike, where the extra bash protection is a must for aggressive riders or on your DH rig. With the popularity of clutch derailleurs, it is no longer necessary to run a chain guide with a lower roller to effectively tension your chain. DH racers and Bike Park rippers will appreciate the huge reduction in drag with the elimination of the lower roller, without sacrificing any strength or chain retention.

Replacement crank arm for X01 Eagle GXP

SRAM Force crank spiders are for repairing your crank or converting it to different gearing. Available in 110mm and 130mm BCDs.

Wheels Manufacturing FSA PF30 Adapter for 24mm Spindle Cranks adapts 24mm Spindle Cranks (Shimano, FSA, etc.) to work on Pressfit 30 frames with FSA's PF30 bottom bracket installed. Simply tap the adapters into the 6806 bearing in the BB shell, install the spindle and cranks. Use our Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. - Machined engineering-grade Delrin - 48g/pr *NOTE: The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter

- XT M8130 12 speed crankset - Fits 157mm SuperBoost MTB frames - Hollow forged crank maximizes power transfer while limiting weight - Direct mount chainring type (TL-FC41 tool included) - Q-factor: 181mm - Chainline: 56.5mm

Race Face Crank Arm Fixing Bolts - M18 Crank Bolt - Fits 15SX/Atlas/SixC CINCH - Not self-extracting

CAMO Spider - Made from Aluminum alloy for light weight - Includes 5 black chainring bolts

The Wolf Tooth CAMO BashSpider is a crankset-mounted boost bash ring. This is a spider with an integrated bash ring for use with direct mount cranksets. The CAMO BashSpider pairs with a CAMO chainring to complete the CAMO System. - A CAMO chainring is required to complete this system - The "rolling" ability of the BashSpider allows the rider to move easily over obstacles - Bash rings that are mounted on the crankset are better supported than bash rings that are mounted to the frame or bottom bracket - M5 (minus 5mm - Boost) is dished towards the frame for 52mm chainline for bikes with Boost spacing - Will fit CAMO chainrings from sizes 28T-34T round or 30T-32T elliptical - Includes mounting bolts - Designed to work with SRAM cranksets that have a removable spider

Protect your 1x investment with this bashguard designed for Shimano Symmetrical 96 BCD cranksets. - Only compatible with symmetrical 96 BCD cranks - Made from aluminum alloy

Machined engineering-grade Delrin inserts for adapting bottom brackets to a different type of crankset spindle. - Adapts PF30 and Cannondale BB30-73A bottom brackets for use with Hollowtech II cranksets - Delrin adaptors fit between bearings and crank spindle - BB Shell Width (mm): 68 mm , 73 mm - Spindle Interface Type: Hollowtech II - BB/Frame Interface: PF30

SRAM’s cranks are strong and tough, ready for any kind of ride. So it’s inevitable that pedal strikes and debris will chip away at the end of the crank. SRAM’s Carbon Crank Boot is an upgrade that combats the wear and tear that comes with hard riding. The boot protects the crank from surface damage and keeps the rider’s style perfectly in tact. - Injection molded plastic crank arm protection - Perfect way to protect your carbon crank investment from scratches and dents from pedal strikes - Material: Injection molded plastic - Recommended Group: XX1, X01, XX, X0

The new Gen 3 single-sided Stages Power L meter is built on to a non-drive-side Shimano Saint M820/M825 crank arm. Stages Power for DH. From the death defying rides of the Atherton's, Danny Hart and Jill Kintner, Stages Power is the tool to help anyone explore their best. For downhill bike riders we offer a Stages Power meter available as a power meter only non-drive crank arm for existing Shimano Saint cranks. Active Temperature Compensation as standard equipment. Consistency of measurement is the most important feature of a power meter. Stages Power was the first meter to make temperature compensation an automatic process ensuring accurate readings no matter the environmental conditions. Individual meter calibration for the most accurate results. Stages Power meters are calibrated individually to ensure a +/- 1.5% accuracy level. Individual calibration means that you can trust the data produced by our system. Additional features: - ± 1.5 % accuracy in all conditions - Active temperature compensation - Accelerometer based cadence measurement - Wirelessly upgradable firmware - LED indicator displays battery level at start up (with no need for connect to an app) and confirms successful zero reset - Updated accelerometer and addition of gyroscope for improved cadence resolution - Upgraded BLE and ANT+ radios offer a 6X improvement of data transmission strength Specifications - Power meter housing: low profile design, with robust door interface - Weight: Only adds 15g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) when used as a single sided meter - Power range (Watts): 0 to 5000 - Cadence range (rpm): 10-220 - Water resistance rating: IPX7 In the box: - Power Meter - High quality CR2032 coin cell battery - Lifetime access to Stages Link for power meter management and firmware upgrades. - 2 months free access to Stages Link premium training and coaching features. - Product Identification Card with Serial Number and ANT+ I.D. Number. - User Guide

The new Gen 3 single-sided Stages Power L meter is built onto a non-drive-side Campagnolo Record 12s crank arm. Tour Proven Stages Power has carried riders to three consecutive Tour de France victories, plus many more world and national championships. If you believe racing provides the world's best product-proving ground, then Stages Power is proven as the world's best power meter. Active Temperature Compensation as Standard Equipment Consistency of measurement is the most important feature of a power meter. Stages Power was the first meter to make temperature compensation an automatic process, ensuring accurate readings no matter the environmental conditions. Individual meter calibration for the most accurate results. Stages Power meters are calibrated individually to ensure a +/- 1.5% accuracy level. Individual calibration means that you can trust the data produced by our system. Additional features: - +/- 1.5 % accuracy in all conditions - Active temperature compensation - Accelerometer-based cadence measurement - Wirelessly upgradable firmware - LED indicator displays battery level at start up (with no need to connect to an app) and confirms successful zero reset - Updated accelerometer and addition of gyroscope for improved cadence resolution - Upgraded BLE and ANT+ radios offer a 6X improvement of data transmission strength Specifications: - Accuracy: +/- 1.5% - Power meter housing: low-profile design with robust door interface - Weight: Only adds 15g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) when used as a single-sided meter - Power range (Watts): 0 to 5000 - Cadence range (rpm): 10-220 - Water resistance rating: IPX7 Sizing Options: - Lengths: 170mm, 172.5mm, 175mm Compatibility: This Campagnolo Record 12 Speed based Stages Power meter non-drive-side crank arm is only meant for use paired with a drive-side Campagnolo Record or Chorus crank arm. It will NOT mate with a Campagnolo Super Record crank arm. - Frame Compatibility: Most frames - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibility: Stages Link, Training Peaks, Strava, Garmin Training Center, and others